Details
![Dynojet autotune review Dynojet autotune review](https://www.dynojet.com/media/catalog/product/a/u/autotune-power-commander-v-single-channel-kit-at-200_01_1.jpg?quality=70&fit=bounds&height=700&width=700&canvas=700:700)
Product Overview Don’t have a dyno tuning center nearby? Best android games free download cooking game. Are you more of a D.I.Y. type? Are you constantly changing parts on your bike? If you answer 'yes' to any or all of the questions above, then our Auto Tune kit is for you. The Dynojet Auto Tune kit is an 'add-on' accessory that can be used with any of our Power Commander V’s. It connects to the PCV with a single cable and requires only a ground and +12 volt connection to be made to install (Harley models include connector for plugging directly into the bikes’ +12 volt line). If your exhaust does not already have one, a 'weld in' O2 sensor bung and cap is included.
'Well, how does it work and what does it do for me?' We have taken virtually the same technology that our patented Tuning Link dynamometer software (for automated Dyno tuning) uses, along with Bosch Wide Band O2 sensors and miniaturized it to be used on your bike, ATV, or UTV, while you ride. Once installed, the Auto Tune kit monitors the fuel mixture (by installing the included Wide Band O2 sensor in the exhaust). It then sends this information to the Power Commander V and automatically corrects it while you ride. Auto tune bass guitar. Each map that we offer has preset Air/Fuel ratio values included that we find to be the best overall settings. This lets you simply plug in the unit and let it do the work. For Harley Davidson models we even monitor and adjust each cylinder individually for increased precision as on these models required fueling can vary significantly between the front and rear cylinder. For advanced users that would like to change the Air/Fuel ratios from our baseline they are fully adjustable. Each throttle opening/RPM combination is individually adjustable, so that you can have both fuel economy, during cruise, while maintaining peak output at larger throttle openings. For most models of bikes it is also possible to adjust the Air/Fuel ratios 'per gear'. This gives you total control of the fueling in every gear and throttle/RPM area if required. The Auto Tune kit can be configured to run and correct at all times or by using the 'map switch port' on the PCV. Nexus vst expansions free crack. You can set it up so that you can switch back and forth between the tuning modes and the base map settings. You can also configure the Auto Tune kit to wait until the bike is at a certain operating temperature before beginning to make adjustments.
- Jun 06, 2012 Power Commander 5/AutoTune install questions/help, 2011 R1. You should use the o2 optimizer supplied with the Power Commander, unless you have found some way to disable or eliminate the stock o2 sensor through ECU programming (i.e. JETT tuning, ECU unleashed, or equivalent ECU reflash). If you add the Autotune to this setup then you.
- Sep 25, 2018 My problem is the autotune will not work with the power commander. I have completed the installation as per instructions, setup the software, but there are no values in the trim tables after a 150km ride or any ride.???? I suspect that the o2 sensor is at fault. Little annoyed after spending big bucks on the setup. Any help much appreciated.
- Apr 25, 2019 If your going to tune a turbo bike by yourself and have a power commander and auto tune you should buy the pod 300. The pod 300 lets you data log. You will want to data log you wot pulls and your cruise to make sure everything is tuned. On a turbo bike I would add fuel in before even tuning.
Power Commander Autotune Problems
Summary of Contents for Dynojet Autotune. Page 1. The Autotune kit when used in conjunction with the PCV allows the bike If necessary type in different values in the cells. Multiple cells can be to be automatically tuned to a target air/fuel ratio. To use this feature highlighted.